CLICK TO CALL: 877-432-2559    |  EMAIL NOW: sales@logojet.com  |  LogoJET is a Woman-Owned Business

UV Transfer Film (UV DTF)

UV Transfer Film · UV DTF · UV Direct-to-Film

Print on everything your flatbed can't touch.

Add UV DTF to the UV printer you already own. Two supplies, no second machine.

Works with any UV LED printer No heat press Starter kit — $350
Carrier film onApplied

One sheet, 54 transfers, 0.2" spacing. Drag to peel.

UV DTF (UV direct-to-film) turns your UV printer into a decal and label printer — but without the weeding. You print onto a two-layer film instead of onto the product, laminate, peel, and press it on. Fine detail, small type and intricate shapes all transfer intact, because there's no material to cut away by hand. It applies to items a flatbed can't print directly: curved bottles, oversized panels, recessed surfaces, heat-sensitive goods. No heat press, no adhesive powder. Shops also call it logo film printing, and any UV LED printer can do it with transfer film and a thermal laminator.

Compatibility

Can my printer do UV DTF?

Yes. If your printer cures with UV LED, it can print UV DTF transfers. If you have clear gloss/varnish, the results are even better. The film loads onto the bed like any other flat substrate — the difference is in the print settings and the finishing step. Add any thermal pressure laminator and you can produce good-quality UV DTF sheets.

Process

How UV DTF works, step by step

Five steps from file to finished product. Total time for a full sheet can range from 5 to 10 minutes depending on what layers and printer model you are using. When you maximize the sheet with as many prints as possible, you improve on both cost and productivity.

Prepare the artwork

Build your design at final size in your design software — Adobe Illustrator, Photoshop, Corel, etc. Your artboard is 11.75" × 16.5" to match Film A. Place your art on the sheet and step and repeat with a minimum of 0.2" on the X and Y spacing to allow space for cutting.

Estimated 2 minutes · Design software

Load Film A and print

Load Film A and remove the clear liner to expose the glue surface — now it's ready to print. UV lamps cure the ink as it lays down, so there is no drying step and no adhesive powder.

5–10 minutes · Depends on layers and printer model

Laminate to Film B

Run Film A and Film B together through the thermal laminator at 175°F (80°C) on speed 1, the lowest setting. Film B picks up the adhesive layer.

30 seconds · Thermal laminator

Cut and peel

Trim around each design, then peel the A film away. Your design stays on the B carrier.

2 minutes · Scissors or cutter

Apply

Press onto a clean, dry surface. Burnish firmly from the center out, then peel the carrier away. No heat, no press.

~30 sec per piece

Applications

What you can decorate with logo film printing

Curved and cylindrical

Tumblers, bottles, mugs, cans, jars, pens, helmets.

Oversized or fixed

Signage, cabinetry, doors, appliance panels, furniture — anything larger than your print bed.

Recessed or irregular

Textured cases, ribbed drinkware, molded plastics, hardware with raised edges.

Heat-sensitive

Candles, cosmetics packaging, electronics, coated goods that won't survive a heat press.

Hard non-porous, generally

Glass, ceramic, metal, acrylic, rigid plastic, sealed wood, leatherette.

Gang-printed short runs

Multiple designs on one sheet, cut apart and applied to different products from a single pass.

Where UV DTF isn't the right tool

Fabric and apparel (use standard DTF), heavily porous or unsealed raw wood, silicone and other low-surface-energy plastics, and any item facing dishwasher exposure or abrasive commercial washing.

Comparison

UV DTF vs. direct-to-object, DTF and sublimation

Four methods, four jobs. Most shops end up running two of them.

UV DTF Direct-to-object UV DTF (standard) Sublimation
Best for Hard goods a flatbed can't fit or reach Flat, rigid items that fit the bed Cotton, poly and blend apparel Poly fabric and coated blanks
Surfaces Glass, metal, ceramic, acrylic, plastic, sealed wood Same — but must lie flat Textiles Polyester and polymer-coated only
Curing UV LED, instant UV LED, instant Heat + adhesive powder Heat + pressure
Heat press Not needed Not needed Required Required
White ink Yes Yes Yes No
Curved surfaces Yes Rotary attachment only Limited With a wrap fixture
Finish Raised, dimensional, glossy Flat to slightly raised Flexible, soft hand Flat, dye-in-substrate
To add it Film + laminator Nothing — you own it DTF printer + oven + press Sublimation printer + press

Cost

What it costs to add UV DTF

Work out your cost per transfer and how many you can gang onto a single sheet.

×

11.75" × 16.5"

Based on Film A at $150 per 100-sheet pack.

Transfers per sheet—
Material cost per transfer—
Monthly material cost—
Sheets needed per month—

Supplies

What you need

One machine and three supplies. The laminator is the only equipment purchase — everything else is consumable.

Testing the waters

UV DTF Materials Starter Kit

Standard, gold and silver Film A sheets plus Film B — enough to test, sample and run your first transfers before committing to full rolls and packs.

$350
Sample-sized quantities
Shop the kit

Technique

Three ways to print it

Standard print

Baseline settings for full-color transfers on light and dark substrates. White underbase, single pass.

Read the guide

Clear varnish

A raised gloss layer for dimensional texture and a premium hand-feel on awards and packaging.

Read the guide

Foil

Gold and silver foil applied in-process for a true metallic finish that toner and ink can't reproduce.

Read the guide

Watch

See the full process

Troubleshooting

When a transfer doesn't behave

Small letters not transferring

Squeegee, warm, peel slow

Work the transfer down firmly with a squeegee. On older printed film, warm the glue slightly with a heat gun, then peel at a 45° angle and go slowly.

Cloudy laminate

Check temp and speed

Running the laminator too cool or too fast traps air between layers. Target 175°F (80°C) on speed 1.

Foil not taking

Layer order and cure

Foil needs an uncured or partially cured surface to bond to. Verify layer order in the foil settings profile.

Weak adhesion on plastic

Surface energy

Low-surface-energy plastics — polypropylene, silicone — resist bonding. Test a sample before a production run.

Colors look dull

White underbase

On dark or transparent substrates, missing or thin white underbase flattens everything above it. Check the underbase in your RIP.

Design tears on peel

Peel angle and speed

Peel at a 45° angle and go slowly. Fine detail and thin strokes need the most patience.

Questions

UV DTF, answered

Can I do UV DTF with a UV flatbed printer I already own?
Yes. Any UV LED flatbed printer can print UV DTF transfers. You need transfer film and a thermal laminator — you don't need a second printer.
What's the difference between UV DTF and regular DTF?
UV DTF uses UV-curable ink cured instantly by UV light, and applies to hard non-porous surfaces with pressure alone. Standard DTF uses water-based ink plus adhesive powder, requires a heat press, and is made for fabric. Different inks, different films, different end products.
Do I need a heat press for UV DTF?
No. UV DTF transfers apply with firm hand pressure. That's what makes them viable on heat-sensitive items and on products too large or awkward for a press.
What surfaces does UV DTF work on?
Hard, smooth, non-porous surfaces: glass, ceramic, metal, acrylic, rigid plastic, sealed wood, leatherette. Not intended for fabric, raw porous wood, or silicone.
How durable are UV DTF transfers?
Expect up to 2 years of color fastness. For physical durability, a UV DTF transfer performs similarly to — or better than — a vinyl decal. Not recommended for dishwasher exposure.
How many transfers fit on one sheet?
It depends on the size of the graphic you want to print, plus a minimum 0.2" of padding between designs on the X and Y to leave cutting space between logos. Use the calculator above to work it out for your own artwork on an 11.75" × 16.5" sheet.
What supplies do I need to start?
A thermal laminator, Film A (the printed side), and Film B (the adhesive carrier). Gold and silver foil sheets are optional. We sell all of these individually or as a bundled starter kit.
Is UV DTF cheaper than buying a dedicated UV DTF printer?
If you already own a UV flatbed, substantially. A laminator plus your first films runs under $2,500 against five figures and up for a dedicated UV DTF machine — and you keep one workflow and one ink set instead of two.
Can I print metallic or foil effects with UV DTF?
Yes. Gold and silver foil sheets applied during the process produce a true metallic finish. We publish a dedicated foil print-settings guide.
Is logo film printing the same as UV DTF?
Yes. Logo film printing is the everyday name shops use for UV DTF — printing a logo onto transfer film and applying it to a finished product, rather than printing onto the product directly. Same process, same films, same laminator.
Why don't the small letters transfer fully?
It comes down to adhesion. Use a squeegee to work the transfer firmly onto the surface. Depending on the age of the printed film, you may also need slight heat from a heat gun to warm the glue — it then peels like butter. Pull at a 45° angle and go slowly.

Next step

Three ways to start

UV DTF Materials Starter Kit contents

Buy the starter kit

You have the printer and you know what you want to make. Films and foil, shipped.

Shop the kit
A range of products decorated with UV DTF transfers

Request a sample kit

Physical samples on glass, metal and drinkware so you can hand the finish to a customer before you commit.

Request samples
A LogoJET specialist demonstrating UV printing in the demo room

Book a demo

Don't own a UV printer yet? See UV DTF and direct-to-object running side by side on your own products.

Schedule a demo